
ReLL


so im taking my motor out seeing that i have to replace the block when i remember awhile back right after doing my BSR getting a misfire because of a small bb found in cyl 4 ! no biggie removed and everything back to normal! now a yr later i decide to check my IM and find my secondaries like this!!


better believe im goign to check the valves for damage and that piston but now that i remember i did notice a slight torque loss hmmm

Offline

Brandon

uh oh, thats not good. u didnt notice anything while driving besides torque loss? no weird noises or anything?

Offline

ReLL


valve tap but not on that side of the motor on the timing chain side(cly1)

Offline

Brandon

i hear a weird ticking noise at only around 2,000 rpm and its only when the engines cold. once it warms i dont hear it anymore. could this be a butterfly screw?

Offline

ReLL


noo i doubt it because it would cause your engine to misfire because they tend to get stuck in the sparkplug chamber adn cause a mis fire and fowl the plusg but hey it culd be.. but what it really sounds like is valve tap check those buckets

Offline

Brandon

but valve tap is normal correct?

Offline

ReLL


yes especially in our engines.. but sometimes they can get really bad

Offline

www.myspace.com/nyburbs

Has their been any 2006 spec's that have lost butterfly screws?
Offline

ReLL


ivanv06 wrote:
Has their been any 2006 spec's that have lost butterfly screws?
no i dont think so i belive after 2004 nissan put a mesh there to catch them

Offline

www.myspace.com/nyburbs

Blk2k3Specv wrote:
ivanv06 wrote:
Has their been any 2006 spec's that have lost butterfly screws?
no i dont think so i belive after 2004 nissan put a mesh there to catch them
can anyone confirm this?i heard that they loctite the screws from the factory in the 06' but i cant confirm this either...
Offline

ReLL


yeah ive herd that too

Offline

Brandon

ivanv06 wrote:
Blk2k3Specv wrote:
ivanv06 wrote:
Has their been any 2006 spec's that have lost butterfly screws?
no i dont think so i belive after 2004 nissan put a mesh there to catch them
can anyone confirm this?i heard that they loctite the screws from the factory in the 06' but i cant confirm this either...
i know for a fact that they did something in order to further prevent this. i dont know whether its happend to any 2006's, so theres no guarentee but its a much smaller chance of it happening

Offline

clay



for the 06's just pull the upper manifold and change them. 45 min of work to feel better and not have to have a new motor.
Offline

ReLL


boogerboy72 wrote:
for the 06's just pull the upper manifold and change them. 45 min of work to feel better and not have to have a new motor.
With any of the q25's all u have to do is take off the I'M but in the 04 ad up motors I'm pretty sure they did comething to prevent it..weather it was to put a mesh or loctite from factory

Offline

brandon

mine looked way worse them that i should of took a pic, every single butterfly was bent and warped, and one of the betterflys got gammed in my manifold fucking everything up
Last edited by nitrousONLY (2008-10-28 10:36:14)
Offline

Brandon


They never put any mesh in there. They added a lock washer and a bit of loctite. My engine is from an 06 and it had them already thread locked with some loctite. I just took em' off and put some of my own in, just to be sure.
You don't know if that guy a Nissan had a bad day or what. His next shift may have been in 5 minutes and there is a burrito with his name on it.

Offline

ReLL


Ahahaaa Julio May Have Put Taco Sause Instead Of Loctite Lol So Yeh I Guess It Is Better Safe Then Sorry

Offline
Pages: 1