This thread has been viewed by: 46 unique users.
2008-10-20 16:45:20 (11 weeks 2 days 3 hours 19 minutes 24 seconds) #1898868 | | view posts since this #1
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
motor and trans mounts
so i just found out today that my trans mount is torn. anybody got ideas for replacement? i'm not sure if ES makes inserts for those or not. I'm a little pressed for time at the moment, so i just took a quick look in this section, but didn't see anything too promising.
any help is appreciated
Jason
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline
2008-10-20 22:50:36 (11 weeks 1 day 21 hours 14 minutes 8 seconds) #1899270 | | view posts since this #2
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
Re: motor and trans mounts
BUMP
i seriously need some help please!
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline
2008-10-20 22:52:18 (11 weeks 1 day 21 hours 12 minutes 26 seconds) #1899273 | | view posts since this #3
- gurov
- Administrator
- v--- russian chicken
- From: Freehold, NJ
- Registered: 2006-03-08
- Reads: 18065
- Posts: 6933
- Thanks given: 29
- Thanks received: 33
- Vehicle: '04 SE-R Spec V
- 1/4mile: 13.200 @ 107.00 Member #1
- Awards : 4
- Showoff page
- Feedback page
- Website
gennady gurov
Modifications : 58
Re: motor and trans mounts
hmmm.. you could use 3m windowweld to fill it, or get proper urethane from mcmaster carr
04 turbo @ 14 psi -
MegaSquirt-I standalone - unit #0 (fuel only mode), gsquirt board v1.0, Pivot 3 Drive Throttle Controller,
J&S UltraSafeguard individual cylinder knock suppression system, Autosport Wiring Engine Harness
660cc msd injectors, 255 walbro fuel pump, JGY fuel rail, t3/t4 57trim, Coolingmist Varicool Progressive Alky controller,
Shurtank with 150psi alky pump.
05 automatic se-r: upcoming turbo project
04 BMW 325xi - daily driver
Online
2008-10-20 22:55:12 (11 weeks 1 day 21 hours 9 minutes 32 seconds) #1899280 | | view posts since this #4
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
Re: motor and trans mounts
that's what i'm thinking. getting something good. thanks gurov. i'm gonna look into that
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline
2008-10-20 23:20:25 (11 weeks 1 day 20 hours 44 minutes 19 seconds) #1899301 | | view posts since this #5
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
Re: motor and trans mounts
well if filling them is the only option, then i guess that's that.
question: how do i fill the mounts? couldn't find a how-to or anything... forgive me if i'm a dumbass...
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline
2008-10-20 23:25:00 (11 weeks 1 day 20 hours 39 minutes 44 seconds) #1899309 | | view posts since this #6
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
Re: motor and trans mounts
yea, i'm gonna get the prothanes for the subframe. i'm just a little lost. do i need to make some kind of mold to go around the open part of the mount?
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline
2008-10-21 00:01:36 (11 weeks 1 day 20 hours 3 minutes 8 seconds) #1899367 | | view posts since this #7
- specVnismo2004
- Jahnke Kong
- From: J-Ville, FL
- Registered: 2008-03-25
- Reads: 9877
- Posts: 1178
- Thanks given: 5
- Thanks received: 6
- Vehicle: '04 SE-R Spec V Member #4520
- Showoff page
Jason Jahnke
Modifications : 17
Re: motor and trans mounts
ok. so i found a how-to [on a honda forum... i feel so dirty now]
now, how hard should i get?
"If everything seems under control, you're just not going fast enough." -Mario Andretti
Vi Veri Veniversum Vivus Vici
certified nissan technician... really, i am...
Offline